ROC 240 16/05/01 17:07 Page II ROC240 1 11 2 3 4 5 6 12 13 14 15 16 7 17 8 9 10 18 19 20 ROC 240 A B C 2 x AAA (LR03) ROC 240 16/05/01 17:07 Page 1 This remote control was programmed in the factory, so that you can use it to control most of the sets of the THOMSON group's make. For this reason, we recommend that prior to attempting to programme the remote control, you try it out by means of one of the methods described in this user manual. But first of all, you'll have to load the supplied batteries into the remote control. Please keep this guide along with the code list (provided separately), so that you can subsequently programme your remote control for use with other sets. 1 - Description of the key functions 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Standby key. Number keys 0 to 9: these keys have the same functions as those of your original remote control and are used to enter the codes of your different sets. For selecting an external source. Programming the remote control or activating the secondary key features (SHIFT). Videotext: Yes/No. Videotext: Info key. Also enables one to access the menus by pressing the SHIFT key first. OK: To confirm a selection. Also enables one to switch off the TV sound. FAST REWIND: keys printed in grey in these Instructions have the same functions as those of your VCR or your original remote control. STOP RECORD: To record, press the M key twice. Videotext: to stop scrolling pages. Indicator lamp: the red indicator lamp lights up when any key is pressed. Press this key first, before you type in the 2-digit channel number. TV, VCR: use these keys to select the set you want to control. Videotext: Back to TV programme. Videotext: the videotext page recovers the TV picture. Also enables one to quit a menu (exit key). PROG +, PROG -: gives you access to the channels (received by the TV set or the video recorder) in either ascending (+) or descending (-) order. Can also be used for vertical travelling through the menus. VOL -, VOL +: to increase (+) or decrease (-) the volume of the TV set. ZOOM-, ZOOM+: for horizontal travelling through the menus (with sets supporting this feature). FAST FORWARD PLAY PAUSE 17 18 19 20 2 - Testing the not yet programmed remote control 1. Switch on the set you want to control. 2. Position the selector (13) on the type of set to be controlled: TV: television set VCR: video recorder 3. Direct the remote control towards the TV set and try to switch it off by simply pressing the key B (1). Should the set not switch off, you'll have to programme the remote control by means of one of the methods A, B, C or D described hereinafter in chapter 3. 1 GB This Universal Remote Control is compatible with most models of infrared-controlled TV sets and video recorders. ROC 240 16/05/01 17:07 Page 2 GB 3 - Programming the remote control Method A ­ Fast programming with 1-digit subcode Before you start programming, you must find the subcode of the set to be controlled (TV set or video recorder). Refer to the list provided with these instructions, page I of the subcodes. 1. Switch on the set you want to control. 2. Position the selector (13) on the type of set to be controlled: TV: television set, VCR: video recorder 3. Hold down the key SHIFT (4) until the red indicator lamp (11) remains lit (the indicator lamp remains on for a couple of seconds, so that you have time enough to proceed with steps 4 to 6. The indicator lamp flashes to signal that this time is almost up, and then goes off). 4. While the indicator is lit, type in the subcode (example: 1 for THOMSON). 5. Direct the remote control towards the set and try to switch it off by pressing the key B (1). 6. Immediately upon the switching-off of the set to be controlled, press OK (7) to store the subcode. 7. Should the set not switch off, press key B (1) repeatedly, until the set switches off. Between two subsequent key depressions, give the red indicator lamp (11) enough time to extinguish and light up again (about 1 second). Proceeding this way will enable you to see whether the set responds or not. 8. Immediately upon the switching-off of the set to be controlled, press OK (7) to store the subcode. Check of the programming In principle, your set is ready for receiving the remote control commands. Check your remote control for proper functioning by performing the test described on page 4. + Method B ­ 3-digit codes programming Before you start programming, you must find the code of the set to be controlled (TV set or video recorder). Refer to the list provided with these instructions, page II of the codes. 1. Switch on the set you want to control. 2. Position the selector (13) on the type of set to be controlled: TV: television set, VCR: video recorder 3. Hold down the key SHIFT (4) until the red indicator lamp (11) remains lit. The indicator lamp remains on for a couple of seconds, so that you have time enough to proceed with step 4. The indicator lamp flashes to signal that this time is almost up, and then goes off. 4. While the indicator is lit, enter the first digit of the 3-digit code proposed for the set to be controlled (example: 016 for THOMSON). The red indicator then goes off or flashes, if the code is not on the list. 5. Direct the remote control towards the set and try to switch it off by pressing the key B (1). 6. Should the set not switch off, repeat step 3. Then type in the next 3-digit code. Try to switch off the set by pressing key B (1) once. Repeat this procedure by trying out each of the 3-digit codes. Check of the programming In principle, your set is ready for receiving the remote control commands. Check your remote control for proper functioning by performing the test described on page 4. + + 2 ROC 240 16/05/01 17:07 Page 3 Method C ­ Programming by means of code retrieval Should none of the codes work, you still have the possibility of retrieving the appropriate code without having to perform any input. 1. Switch on the set you want to control. 2. Position the selector (13) on the type of set to be controlled: TV: television set, VCR: video recorder 3. Hold down the key SHIFT (4) until the red indicator lamp (11) remains lit. 4. Direct the remote control towards the set and try to switch it off by pressing the key B (1). 5. Immediately upon the switching-off of the set to be controlled, press OK (7) to store the code. 6. Should the set not switch off, press key B (1) as many times as required (up to 200 times), until the set switches off. Between two subsequent key depressions, give the red indicator lamp (11) enough time to extinguish and light up again (about 1 second). Proceeding this way will enable you to see whether the set responds or not. 7. Immediately upon the switching-off of the set to be controlled, press OK (7) to store the code. Check of the programming In principle, your set is ready for receiving the remote control commands. Perform the following tests to check proper functioning: - For a TV set or satellite receiver: press for instance number key 2 to switch over to another channel or to switch the set on, in case it is off. - Video recorder: load a tape and then press B. Try out other remote control keys to find out the range of functions you can control. If you think that not all of the keys are active, repeat the procedure of this programming method to find out the code supporting a wider range of features. Method D ­ Programming for control of a COMBO (combined TV-VCR set) Setting up the remote control for control of a COMBO means that you first programme the television and then the video recorder subset, the combination of which makes up the COMBO set. Before you start programming, you must find the subcode or code of the subset to be controlled (television or video recorder). Refer to the list supplied with this user manual (see page subcodes or codes). 1. Switch on the COMBO you want to control. 2. Set the remote control selector (13) on TV, and then proceed with one of the programming methods A, B or C described above. 3. Set the remote control selector (13) on VCR, and then proceed with one of the programming methods A, B or C described above. 3 GB ROC 240 16/05/01 17:07 Page 4 GB 4 ­ How to retrieve a programmed code It may be useful to retrieve the code programmed in the remote control. 1. Set the selector (13) on the type of set concerned (TV or VCR). 2. Hold down the key SHIFT (4) until the red indicator lamp (11) remains lit. 3. Press SHIFT (4) again briefly. The red indicator lamp flashes once. 4. Press the number keys (0 to 9) in ascending order until the red indicator lamp (11) flashes once. 5. The digit which made the red indicator lamp (11) flash, is the first number of the 3-digit code. Please note it down below. 6. Repeat step 4 to find out the two other numbers of the code. 7. When the third number is found, the red indicator lamp (11) goes off. 5 ­ Check of the programming - For a TV set: press for instance number key 2 to switch over to another channel or to switch the set on, in case it is off. - Video recorder: load a tape and then press B. Try other remote control keys to find out the range of functions you can control. If you think that not all of the keys are active, try the programming Method B or C. When you have retrieved the code of your set, jot it down so that you can use it whenever needed. After battery replacement, you'll have to programme the remote control again. TV CODE VCR CODE 6 ­ The NAVILIGHT system The THOMSON NAVILIGHT system allows you easy access to the settings of your television (TV) or video recorder (VCR) including this feature. 1. Switch on the set you want to control. 2. Set the selector (13) on the type of set concerned (TV or VCR). In the VCR position, make sure that the AV mode is activated for the TV set (the SCART socket must be selected). 3. Press the SHIFT key once and then menu (6). + + 4. To travel through the setting menus, press the SHIFT key once and then use the keys up, down, left and right (16 and 17). 5. Validate with OK (7). 6. To leave the menus, press SHIFT once and then the exit key (15). + You can contact THOMSON by dialing: 0845 601 3093, from 27 November 2000. (For Great-Britain, all calls will be charged at local rate) www.thomson-europe.com 4 ROC 240 16/05/01 17:07 Page 5 Cette télécommande universelle est compatible avec la plupar t des téléviseurs et magnétoscopes commandés par infrarouge. La télécommande a été programmée en usine pour vous permettre de l'utiliser immédiatement avec la plupart des appareils des marques du groupe Thomson. Nous vous conseillons donc de l'essayer avant de la programmer en suivant une des méthodes de cette notice. Mais avant tout, vous devez installer les piles fournies avec la télécommande. Conservez cette notice et la liste des codes séparée afin de pouvoir reprogrammer ultérieurement la télécommande pour commander d'autres appareils. 1 - Description des touches 1 2 Touche Marche/Arrêt. Touches numériques 0 à 9 : ont les mêmes fonctions que les touches numériques de votre télécommande habituelle et servent en plus à entrer les codes des appareils. 3 4 5 6 Sélection d'une source externe. Programmation de la télécommande ou Activation des fonctions secondaires des touches (SHIFT). Télétexte : Oui/Non. Télétexte : Touche Info. Permet aussi d'accéder aux menus en appuyant d'abord sur la touche SHIFT. OK : pour confirmer un choix. Permet aussi de couper le son du téléviseur. RETOUR RAPIDE : les touches repérées en gris dans le texte ont les mêmes fonctions que celles de votre magnétoscope ou votre télécommande d'origine. 7 8 9 10 STOP ENREGISTREMENT. Pour enregistrer, appuyez deux fois sur la touche M. Télétexte : Arrêt de l'alternance des pages. Voyant lumineux : le voyant rouge est allumé lorsqu'une touche est pressée. Appuyez d'abord sur cette touche avant d'entrer le numéro de chaîne à 2 chiffres. TV, VCR : permet de sélectionner l'appareil que vous désirez commander. Télétexte : retour au programme TV. Télétexte : la page télétexte se superpose à l'image du téléviseur. Permet aussi de quitter un menu (touche exit). PROG +, PROG - : permet d'accéder aux chaînes (reçues par le téléviseur ou le magnétoscope) selon un ordre croissant (PROG +) ou décroissant (PROG -). Permet aussi de vous déplacer verticalement dans les menus. VOL -, VOL + : permet d'augmenter (+) ou de diminuer (-) le volume sonore du téléviseur. ZOOM -, ZOOM + : Touches directionnelles pour vous déplacer horizontalement dans les menus et fonction zoom (appareils ayant cette fonction). 11 12 13 14 15 16 17 18 19 20 AVANCE RAPIDE LECTURE PAUSE 2 - Essai de la télécommande sans l'avoir programmée 1. Mettez en marche l'appareil que vous souhaitez commander. 2. Positionnez le sélecteur (13) sur le type d'appareil à commander: TV : téléviseur VCR : magnétoscope 3. Dirigez l ...