DIGITAL PHOTO PRINTER P-11 Instruction Manual Manuel d'utilisation Bedienungsanleitung Manual de instrucciones ENGLISH FRANÇAIS DEUTSCH ESPAÑOL 2 40 80 120 Thank you for purchasing the P-11 Digital Photo Printer. Read this manual carefully prior to use to ensure optimum performance. ENGLISH For customers in North and South America For customers in USA Declaration of Conformity Product Name : Digital Photo Printer Model Number : P-11 Trade Name : OLYMPUS Responsible Party : Address : Two Corporate Center Drive, PO Box 9058, Melville, NY 11747-9058 U.S.A. Telephone Number : 1-631-844-5000 Tested To Comply With FCC Standards FOR HOME OR OFFICE USE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Notice · Radio and Television Interference Change or modifications not expressly approved by the manufacturer may void the user's authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Adjust or relocate the receiving antenna. - Increase the distance between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult your dealer or an experienced radio/TV technician for help. WARNING: The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with device. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Any unauthorized changes or modifications to this equipment would void the user's authority to operate. For customers in Canada This Class B digital apparatus complies with Canadian ICES-003. For customers in Europe "CE" mark indicates that this product complies with the European requirements for safety, health, environment and customer protection. "CE" mark printers are intended for sales in Europe. This symbol [crossed-out wheeled bin WEEE Annex IV] indicates separate collection of waste electrical and electronic equipment in the EU countries. Please do not throw the equipment into the domestic refuse. Please use the return and collection systems available in your country for the disposal of this product. Trademarks Windows is registered trademark of Microsoft Corporation. All other brand names and product names appearing in this instruction manual are trademarks or registered trademarks of their respective holders. 2 Contents Introduction Safety precautions ..................................................................................... 4 Care and storage ....................................................................................... 9 What this printer can do ........................................................................... 10 Checking the accessories ........................................................................ 11 Identifying the parts.................................................................................. 12 Preparation Connecting the power supply and turning on/off the printer..................... 14 Loading the ink ribbon cartridge............................................................... 16 Loading paper .......................................................................................... 19 Removing the paper tray from the printer ......................................................... 19 Loading paper into the paper tray..................................................................... 20 Inserting the paper tray into the printer............................................................. 22 Introduction ENGLISH Printing Printing pictures from a digital camera..................................................... 23 About PictBridge compatible digital cameras ................................................... 23 Connecting a digital camera to the printer ........................................................ 23 Using the digital camera to control the print operation ..................................... 24 Printing pictures from a computer ............................................................ 26 Installing the printer driver (during initial setup) ................................................ 26 Connecting a computer to the printer ............................................................... 26 Printing.............................................................................................................. 28 Preparation For Your Reference If an indicator is lit or blinking ................................................................... 30 Troubleshooting ....................................................................................... 31 If paper is jammed ............................................................................................ 32 If the ink ribbon cartridge is removed during printing........................................ 33 Printing For Your Reference Replenishing the paper supply and replacing the ink ribbon cartridge..... 34 If paper runs out during printing........................................................................ 34 If the ink ribbon runs out during printing ........................................................... 34 About the print pack (ink ribbon cartridge and paper) .............................. 35 Specifications ........................................................................................... 37 Service and maintenance......................................................................... 38 Definition of terms .................................................................................... 39 3 Introduction Safety precautions ENGLISH Various icons are used in this manual to indicate correct product use, and help prevent property damage and injury to you and others. The meanings of these icons are described below. Icon Description WARNING CAUTION Failure to follow instructions indicated by this icon may lead to serious injury or death. Failure to follow instructions indicated by this icon may lead to injury or property damage. Precautionary notations are indicated by the following symbols. Introduction Icon Description Do not perform this action. You are strongly encouraged to perform this action. Unplug the device from the power source. Preparation Do not disassemble. Avoid contact with water and other liquids. Do not touch if your hands are wet. For Your Reference Printing 4 Safety precautions WARNING If this device acts abnormally, unplug it Do not use the printer if it emits smoke, unusual smells, strange sounds, or becomes unusually warm. Use under these conditions may cause fire or electric shock. Turn off and unplug the printer. Then contact your nearest Olympus service center. Should any liquid or foreign objects get into the printer, unplug the power cord Do not allow any liquids, metals, or flammable objects to get into the printer through the ventilation holes. This may cause fire or electric shock. Turn off and unplug the printer. Then contact your nearest Olympus service center. If the printer cabinet is damaged, unplug the power cord Do not use this device if the cabinet (body) is damaged. Use in this condition may cause fire or electric shock. Turn off and unplug the printer. Then contact your nearest Olympus service center. If the power cord is damaged, unplug it Do not use a damaged power cord. Use in this condition may cause fire or electric shock. Turn the printer off, and unplug the power cord being careful not to touch any exposed wires. Then contact your nearest Olympus service center. ENGLISH Introduction Preparation Printing For Your Reference 5 Safety precautions WARNING Do not damage the power cord Do not damage or modify the power cord. A damaged power cord may result in fire or electric shock. To prevent the cord from becoming damaged, DO NOT: pull on the cord to unplug it, bend the cord excessively, or place heavy objects on the cord. If the power cord is damaged, contact your nearest Olympus service center. Do not disassemble or modify the printer The printer has both hot and high voltage parts on the inside. Touching these parts may result in burns, electric shock, and/or damage to the printer. Never attempt to disassemble or modify the printer as this may lead to electric shock or printer malfunction. For service or repair, contact your nearest Olympus service center. Do not allow liquids near the printer If liquid gets into the printer, it may result in fire or electric shock. Do not place heavy objects on the printer Heavy objects may damage the printer cabinet, resulting in fire or electric shock. Damage may also result from the printer being dropped or falling. Do not install the printer in the following places To prevent fire, electric shock, and printer malfunction, do not install the printer in the following places: Dusty, humid, or oily places Should any dust or liquid get into the printer, it may result in fire or electric shock. Extremely hot places Do not expose the printer to direct sunlight (for example, inside a car or near a window) or extremely high temperatures (for example, near a heater). Doing so may damage the printer cabinet, resulting in fire or electric shock. Use the printer in an environment with an ambient temperature between 5 to 35°C (41 to 95°F) and humidity of 20 to 80%. ENGLISH For Your Reference Printing Preparation Introduction 6 Safety precautions WARNING Do not use the printer in the following places Unstable or inclined surfaces. Outdoors (particularly on beaches, etc.), or places that expose the printer to excessive dust or debris. Places subject to rain, dripping, or enclosed places where condensation could occur such as inside a plastic bag. Do not use the printer with an AC adapter or power cord other than that specified/provided Do not use the provided AC adapter or power cord with any other devices Provide correct voltage Incorrect voltage may damage printer parts. Use with incorrect voltage may cause fire or electric shock. Connect the power cord correctly/safely For example, if the power cord is plugged in loosely, it may cause a fire or electric shock. Push the plug all the way into the outlet. Make sure that excessive dust and debris do not accumulate on the power cord Dust and debris may conduct electricity, which can cause fire and electric shock. If excessive dust and debris accumulate on the cord, unplug the cord and clean it. Always unplug the power cord during an electrical storm The induced electricity from storms may cause fire, electric shock, or printer malfunction. Do not hold the power cord plug with wet hands Doing so may result in fire, electric shock, or printer malfunction. Be sure your hands are dry before handling. For Your Reference Plug the printer directly into an outlet Avoid plugging into a socket that is already being used by several appliances. ENGLISH Introduction Preparation Printing 7 Safety precautions CAUTION Do not put the printer on an unstable surface Do not put the printer on an unstable surface such as a shaky table. Injury may result from the printer being dropped or falling. This could also damage the printer or cause the printer to malfunction. Do not touch the non-user-serviceable parts inside the printer Doing so may cause injury or burns. This applies especially to children and those unfamiliar with the printer. Do not move the printer when the power cord is taut Moving the printer when the power cord is taut may damage the cord. Using the printer when damaged may cause fire or electric shock. When moving the printer, unplug and bundle the power cord. Do not unplug the printer by jerking or pulling on the power cord To unplug the power cord, hold it by the plug. Pulling on the cord may damage it, possibly resulting in fire or electric shoc ...