Universal Bluetooth® Headset H680 H680 MOTOMANUAL Figure 1 7 6 5 1 3 2 3 4 2 1 1 Figure 2 Figure 3 Figure 4 2 Figure 5 Figure 6 3 Figure 7 Indicator Light Power Switch 4 English European Union Directives Conformance Statement Hereby, Motorola Inc., declares that this H680 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. You can view your product's Declaration of Conformity (DoC) to Directive 1999/5/EC (the R&TTE Directive) at www.motorola. com/rtte. Caring for the Environment by Recycling When you see this symbol on a Motorola product, do not dispose the product with household waste. Recycling Mobile Phones and Accessories Do not dispose of mobile phones or electrical accessories, such as chargers or headsets, with your household waste. In some countries or regions, collection systems are set up to handle electrical and electronic waste items. Contact your regional authorities for more details. If collection systems aren't available, return unwanted mobile phones or electrical accessories to any Motorola Approved Service Centre in your region. FCC Notice to Users Users are not permitted to make changes or modify the device in any way. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. See47-CFR-Sec.-15.21. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See-47-CFR-Sec.-15.19(3). 5 English Before you begin See figure 1 on page 1. Take a moment before you get started to familiarize yourself with your new H680 Bluetooth Hands-free Headset. Along with your headset, a charger case is provided for both charging and storage. Bluetooth headset 1. Power button 2. Call button 3. Indicator light 4. Microphone 5. Charging contacts 6. Volume buttons 7. Speaker Charger case 1. Charger port 2. Charging contacts 3. Charger cover 6 English Wearing your headset See figure 2 on page 2. Your H680 headset is supplied with multiple ear buds. The ear bud is fitted onto the end of your headset's earpiece speaker, and placed onto your ear when using your headset. Your headset's performance is greatly dependent upon achieving a good fit on your ear. Therefore, we recommend trying all the supplied ear buds with your headset. You can wear your H680 headset on your left of right ear. The headset comes ready for the right ear. Placing the headset on your ear: see figure 3 on page 2. Placing the headset on the left ear: see figure 4 on page 2. Charging your headset See figure 5 on page 3. Important: Your headset must be turned off when charging. 1. Plug the Motorola charger into the port on the charger case. 2. Place the headset into the charger case ensuring that charging contacts on the headset and charging case connect. The indicator light turns red when the battery is charging. It may take up to 1 minute for the indicator light to turn on. When the headset's battery is fully charged (about 2.5 hours), the indicator light turns off. Note: Headset is NOT functional while charging. 7 English Storing your headset See figure 6 on page 3. The charger case provided is used to charge and store your headset. When not using your headset, you should place it in the charger base. Be sure to turn the headset off before placing it into the charger case. The charger cover can be placed on top of the charger case, or underneath it to provide support for desktop placement. Turning headset on and off See figure 7 on page 4. To turn your headset on, slide the Power switch on (towards Power symbol on headset). The indicator light is steadily purple for several seconds, then flashes blue (if paired and connected with another device) or is steadily blue (if ready to be paired). To turn your headset off, slide the Power switch off. The indicator light will turn off. 8 English Pairing your headset Your phone's Bluetooth feature is off by default. To use your headset, you must turn on the Bluetooth feature in your phone. Please check your phone's user's guide. Note: The Bluetooth feature remains on until you turn the feature off. Before you can use your headset, you must pair it with your phone. 1. Ensure headset is in pairing mode Remove headset from charging base and power it on. The indicator light flashes to initiate easy pairing. After a few moments, the indicator light will be steadily lit in blue to indicate headset is in pairing mode. If the headset does not enter into pairing mode, see "Troubleshooting" section. 2. Set your phone to look for your headset · Perform a device discovery from the phone. For details about device discovery, consult your phone's user's guide. The phone lists Bluetooth devices it finds. · Select Motorola H680 in the list of discovered devices and confirm by following the on-screen prompts. · When prompted by the phone, enter the passkey 0000 and confirm. Pairing is successful when the headset indicator changes from steadily lit to flashing blue. 9 English Test and Use Your phone and headset are now paired and ready to make and receive calls. To confirm they are successfully paired and operating properly, place the headset over your ear and make a call from your phone. You will hear ringing from the headset. After you have successfully paired your phone and headset, you do not need to repeat these steps each time you use the headset. Using your headset: Making & receiving calls Your headset supports both hands-free and headset profiles. Accessing call functions depend upon which profile your phone supports. See your phone's user's guide for more information. Note: Some features are phone/network dependent. Function Receive a call End a call Reject a call Redial last call Make a voice dial call Action Tap the Call button Tap the Call button Press and hold either volume button until you hear 2 descending tones Press and hold the Call button until you hear 2 ascending tones Tap the Call button and speak the name after the tone Answer a second incoming call Tap the Call button Disable the indicator light Turn headset off Press and hold both volume buttons AND simultaneously turn headset back on Tap both Volume buttons Mute or un-mute a call 10 English Indicator lights With charger plugged in Headset indicator Steady red Off Headset status Charge in progress Charging complete With no charger plugged in Headset indicator Off Steady purple Steady blue 10 quick purple flashes Slow blue flash Quick blue flash Slow blue pulse Slow purple pulse Slow red flash Quick red flash Headset status Power off Powering on/off Pairing/Connection mode Connection successful Standby (not on a call) Incoming call Connected (on a call) Connected (on a muted call) Idle (not connected) Low battery Note: After 30 minutes on a call or of inactivity, the light stops flashing to conserve battery power, but the headset remains in standby mode. 11 English Audio tones Audio tone Ring tone Single high tone High to low tone Single high tone when pressing volume button 2 ascending tones 2 descending tones Low to high tone No audio indications: deteriorating quality 2 tones repeated every 30 seconds Headset status Incoming call Phone network not available End call Volume at maximum or minimum Mute enabled Mute disabled Pairing confirmation/voice activation Out of range Low battery 12 English Troubleshooting My headset will not charge Make sure your headset is turned off when charging. Your headset will not charge in the charger case while powered on. My headset will not enter pairing mode Make sure that any devices previously paired with the headset are turned off. If the indicator light is not steadily lit in blue, turn off both the other device and headset, wait 10 seconds, then turn headset back on. Wait for the indicator light to become steadily lit in blue, indicating the headset is now in pairing mode. My phone doesn't find my headset Make sure the indicator light on your headset is on (lit in blue) and steady when your phone is searching for devices. My headset worked before but now it's not working Make sure your phone is on and the Bluetooth feature is turned on in your phone. If the Bluetooth feature was turned off or was turned on only temporarily, you may need to restart the Bluetooth feature and pair your phone and headset again. If you have any additional questions, please call your hotline number (0870-9010-555) or visit us at www.hellomoto.com. 13 Français Déclaration de conformité aux directives de l'Union Européenne Par la présente Motorola Inc., déclare que l'appareil H680 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/EC. Vous pouvez consulter la Déclaration de conformité de votre produit à la Directive 1999/5/EC (la Directive R&TTE) à l'adresse www.motorola.com/rtte. Protection de l'environnement par le recyclage Lorsqu'un produit Motorola arbore ce symbole, ne le jetez pas dans votre poubelle. Recyclage des téléphones portables et accessoires Ne jetez aucun téléphone portable ou accessoire électrique, comme un chargeur ou un kit piéton, dans votre poubelle. Des systèmes de collecte permettant de traiter les déchets électriques et électroniques sont progressivement mis en place. Renseignez-vous localement pour plus d'informations. En l'absence de système de collecte, renvoyez les téléphones portables et accessoires électriques à l'un des Centres de Service agréé par Motorola le plus proche. Avis aux utilisateurs L'utilisateur n'a le droit d'apporter ni changement ni modification à l'appareil, de quelque façon que ce soit. Le droit de l'utilisateur de faire usage de l'appareil peut être annulé par des changements ou modifications non expressément approuvés par l'entité en charge de la conformité de l'appareil aux normes. Voir 47 CFR Sec.15.21. Cet appareil est conforme à la clause 15 des règlements de la FCC. Son fonctionnement est sujet aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence nuisible, et (2) cet appareil doit accepter toute interférence, y compris l'interférence pouvant causer un fonctionnement inapproprié. Voir 47 CFR Sec.15.19 (3). 14 Français Avant de commencer Voir figure 1, page 1. Prenez le temps de vous familiariser avec votre nouvelle oreillette mainslibres Bluetooth H680. Un boîtier est fourni avec votre oreillette, destiné à la fois à la charge et au rangement. Oreillette Bluetooth 1. Bouton marche/arrêt 2. Bouton d'appel 3. Voyant 4. Microphone 5. Contacts de charge 6. Boutons de volume 7. Haut-parleur Boîtier de charge 1. Port de charge 2. Contacts de charge 3. Couvercle 15 Français Port de votre oreillette Voir figure 2, page 2. Votre H680 possède plusieurs embouts pour oreilles. L'embout est fixé sur l'extrémité du haut-parleur de l'oreillette. Il se place directement dans l'oreille. La qualité de son de votre oreillette dépend pour beaucoup du port de celle-ci sur votre oreille. Il est donc recommandé d'essayer tous les embouts. Vous pouvez porter votre H680 à l'oreille gauche ou droite. Par défaut, le tour d'oreille est installé sur l'oreillette pour qu'elle soit portée à l'oreille droite. Port à l'oreille droite : Voir figure 3, page 2. Port à l'oreille gauche : Voir figure 4, page 2. Mise en charge de votre oreillette Voir figure 5, page 3. Important : votre oreillette doit être éteinte pendant la charge. 1. Branchez le chargeur Motorola dans le port du chargeur. 2. Placez l'oreillette dans le boîtier en vérifiant la connexion entre les contacts de charge sur l'oreillette et le boîtier. Le voyant rouge s'allume quand la batterie est en charge. Il peut prendre jusqu'à 1 minute pour s'allumer. Quand la batterie de l'oreillette est complètement chargée (environ 2h30), le voyant s'éteint. Remarque : l'utilisation de l'oreillette est impossible pendant la charge. 16 Français Rangement de votre oreillette Voir figure 6, page 3. Le boîtier fourni est utilisé pour charger et ranger votre oreillette. Si votre oreillette n'est pas utilisée, placez-la dans la base du chargeur. N'oubliez pas d'éteindre votre oreillette avant de la mettre dans le boîtier. Le couvercle peut être placé sur le dessus du boîtier ou en dessous pour servir de support de bureau. Allumer/éteindre l'oreillette Voir figure 7, page 4. Pour allumer l'oreillette, glissez le bouton marche/arrêt en position ON (vers le symbole d'alimentation sur l'oreillette). Le voyant reste allumé en violet pendant plusieurs secondes, puis clignote en bleu (s'il y a couplage et connexion avec un autre périphérique) ou reste allumé en bleu (si prêt à être couplé). Pour éteindre votre oreillette, g ...