GB UA PL RO DE HU SK CZ Angle Sander Szlifierka ktowa lefuitor unghiular Winkelschleifer Sarokcsiszoló Uhlová brúska Úhlová bruska INSTRUCTION MANUAL INSTRUKCJA OBSLUGI MANUAL DE INSTRUCIUNI BEDIENUNGSANLEITUNG HASZNÁLATI KÉZIKÖNYV NÁVOD NA OBSLUHU NÁVOD K OBSLUZE SA7000C 1 1 1 1 2 1 005016 2 005017 3 005018 1 2 3 4 005019 5 005020 6 005021 1 A B 1 15 2 2 7 005022 8 005023 9 005024 2 1 3 2 1 001146 10 11 005025 2 ENGLISH (Original instructions) Explanation of general view 1-1. Shaft lock 2-1. Lock button 2-2. Switch trigger 3-1. Speed adjusting dial 6-1. Lock nut 6-2. Abrasive disc 6-3. Rubber pad 7-1. Lock nut wrench 7-2. Shaft lock 9-1. Exhaust vent 9-2. Inhalation vent 10-1. Commutator 10-2. Insulating tip 10-3. Carbon brush 11-1. Brush holder cap 11-2. Screwdriver SPECIFICATIONS Model Disc diameter Spindle thread No load speed (n0) / Rated speed (n) Overall length Net weight Safety class · Specifications may differ from country to country. · Weight according to EPTA-Procedure 01/2003 ENE052-1 ENG901-1 · SA7000C 180 mm M14 0 - 1,500 / 4,000 (min-1) 453 mm 3.4 kg /II · Due to our continuing programme of research and development, the specifications herein are subject to change without notice. Intended use The tool is intended for the sanding of large surface of wood, plastic and metal materials as well as painted surfaces. ENF002-1 Power supply The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire. ENG102-2 · The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another. The declared vibration emission value may also be used in a preliminary assessment of exposure. WARNING: The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used. Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). ENH101-12 · For European countries only Noise The typical A-weighted noise level determined according to EN60745: Sound pressure level (LpA) : 88 dB(A) Sound power level (LWA) : 99 dB(A) Uncertainty (K) : 3 dB(A) Wear ear protection ENG228-4 · Vibration The vibration total value (tri-axial vector sum) determined according to EN60745-2-3: Work mode: disc sanding Vibration emission (ah,SG) : 2.5 m/s2 or less Uncertainty (K) : 1.5 m/s2 If the tool is used for other applications, the vibration emission value may be different. EC Declaration of Conformity We Makita Corporation as the responsible manufacturer declare that the following Makita machine(s): Designation of Machine: Angle Sander Model No./ Type: SA7000C are of series production and Conforms to the following European Directives: 98/37/EC until 28th December 2009 and then with 2006/42/EC from 29th December 2009 And are manufactured in accordance with the following standards or standardised documents: EN60745 3 The technical documentation is kept by our authorised representative in Europe who is: Makita International Europe Ltd, Michigan, Drive, Tongwell, Milton Keynes, MK15 8JD, England 30th January 2009 6. 000230 7. Tomoyasu Kato Director Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN GEA010-1 General Power Tool Safety Warnings WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. 8. Save all warnings and instructions for future reference. GEB036-2 SPECIFIC SAFETY RULES DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to sander safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. Safety Warnings Common for Sanding Operation: 1. This power tool is intended to function as a sander. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. 2. Operations such as grinding, wire brushing, polishing or cutting-off are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury. 3. Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation. 4. The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart. 5. The outside diameter and the thickness of your accessory must be within the capacity 4 9. 10. 11. 12. 13. rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled. The arbour size of backing pads or any other accessory must properly fit the spindle of the power tool. Accessories with arbour holes that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control. Do not use a damaged accessory. Before each use inspect the accessory such as backing pad for cracks, tear or excess wear. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time. Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations . The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss. Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation. Hold power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and shock the operator. Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory. Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control. Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. Regularly clean the power tool's air vents. The motor's fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. 15. Do not operate the power tool near flammable materials. Sparks could ignite these materials. 16. Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock. 17. Kickback and Related Warnings Kickback is a sudden reaction to a snagged rotating backing pad or any other accessory. Snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory's rotation at the point of the binding. Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below. a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken. b) Never place your hand near the rotating accessory. Accessory may kickback over your hand. c) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel's movement at the point of snagging. d) Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback. e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control. Safety Warnings Specific for Sanding Operations: 18. Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback. 19. Check the backing pad carefully for cracks, damage or deformity before operation. Replace cracked, damaged or deformed pad immediately. 20. NEVER use tool with wood cutting blades or other sawblades. Such blades when used on a sander frequently kick and cause loss of control leading to personal injury. 5 14. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. Hold the tool firmly. Keep hands away from rotating parts. Make sure the abrasive disc is not contacting the workpiece before the switch is turned on. When sanding metal surfaces, watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials. Do not leave the tool running. Operate the tool only when hand-held. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. Check that the workpiece is properly supported. Pay attention that the wheel continues to rotate after the tool is switched off. This tool has not been waterproofed, so do not use water on the workpiece surface. Ventilate your work area adequately when you perform sanding operations. Use of this tool to sand some products, paints and wood could expose user to dust containing hazardous substances. Use appropriate respiratory protection. Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. If working place is extremely hot and humid, or badly polluted by conductive dust, use a short-circuit breaker (30 mA) to assure operator safety. Do not use the tool on any materials containing asbestos. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. Always use the correct dust mask/respirator for the material and application you are working with. Ensure that ventilation openings are kept clear when working in dusty conditions. If it should become necessary to clear dust, first disconnect the tool from the mains supply ( use non metallic objects ) and avoid damaging internal parts. SAVE THESE INSTRUCTIONS. FUNCTIONAL DESCRIPTION · CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Shaft lock Fig.1 CAUTION: Never actuate the shaft lock when the spindle is moving. The tool may be damaged. Press the shaft lock to prevent spindle rotation when installing or removing accessories. · Constant speed control Possible to get fine finish, because the rotating speed is kept constant even under the loaded condition. Additionally, when the load on the tool exceeds admissible levels, power to the motor is reduced to protect the motor from overheating. When the load returns to admissible levels, the tool will operate as normal. Soft start feature Soft start because of suppressed starting shock. ASSEMBLY · Switch action Fig.2 CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. ...